Oil and Filter Change: Yamaha V-Star 650 Cruiser

To prepare for an oil change on my neighbor’s 2004 Yamaha V-Star 650 cruiser, I gathered up my tools, laid down some cardboard to catch spills and drips, prepped my recycling containers, and readied the fresh oil and filter. She rode the bike enough to warm it up, then rode it over to my place, so the oil would be nice and warm, and flow out easily when drained.

The V-Star, ready for her oil change, tools and supplies at hand

The V-Star, ready for her oil change, tools and supplies at hand

getting ready

getting ready

Supplies needed:
* 3-4 quarts of 20w50 viscosity motor oil (my neighbor chose Castrol motorcycle-specific synthetic oil). If you choose regular car oil rather than motorcycle oil, the round label on the back should NOT read “energy conserving”. If it does, your clutch may slip from the extra-slippery additives in the oil, intended for use in cars and trucks.
* Fresh crush washer
* Fresh Filter
* Rags/paper towels for cleanup
* ziploc bag to recycle filter after draining
* Latex or nitrile gloves to protect your hands from toxic oil

Tools Needed:
* Socket wrench and/or 17mm metric wrench
* Size 4 and 5 allen wrenches
* funnel
* oil pan
* container for recycling oil

(Find out how to get free oil and filter drainer gear and recycle your oil and filters in San Mateo County, San Francisco, Alameda County, Sonoma County, Napa County, Marin County and Sacramento.)

Yamaha has been making the V-Star 650 motorcycle, with only cosmetic changes, from 1998 to the present. The oil and filter change procedure for all these bikes is substantially similar for all of ’em.

To get the oil pan under this low-slung cruiser, we propped the kickstand up on a brick, giving a little extra room to push the pan beneath the engine.

To get the oil pan under this low-slung cruiser, we propped the kickstand up on a brick, giving a little extra room to push the pan beneath the engine.

After pushing the pan beneath the bike, I got down on the ground on the left side to locate the oil drain bolt. The oil drain bolt is on the rider’s left side of the bike, tucked beneath the frame rail, on the lower left side of the oil pan. I wiggled my 17mm socket onto the bolt and wrenched it loose.

Oil drain bolt on left of oil pan

Oil drain bolt on left of oil pan

The oil drain bolt is reached on the left side of the bike, beneath the frame rail, on the left side of the oil pan.

The oil drain bolt is reached on the left side of the bike, beneath the frame rail, on the left side of the oil pan.

The oil poured out, a small amount of it missing the pan and making a bit of a mess–on the cardboard, fortunately. Oil-contaminated runoff is toxic, so better on cardboard than on your driveway.

Oil draining--most of it into the oil pan!

Oil draining–most of it into the oil pan!

I added a new crush washer to the oil drain bolt and set it aside.

oil drain bolt, with new crush washer

oil drain bolt, with new crush washer

While the engine oil continued to drain, I moved to the filter. The V-Star 650 has a 2-part decorative cover over the oil filter housing, and both pieces need to be removed separately to access the filter. Using my allen wrench, I pulled the 3 bolts from the outer cover and removed it. Allen (also known as hex head) bolts can strip out and cause more trouble than anyone needs, so I used high-quality allen wrenches or socket bits, and used a careful hand to make sure the bolts came out smoothly.

Removing the outer cover of the oil filter housing

Removing the outer cover of the oil filter housing

Outer oil filter cover, removed

Outer oil filter cover, removed

I carefully kept the 3 allen bolts with the outer cover, then began to undo the allen bolts of the inner cover.

Removing allen bolts from the inner oil filter cover

Removing allen bolts from the inner oil filter cover

The bolts holding the inner oil filter cover are different lengths, and each must return to its proper place. Laying them out in a place they won’t be disturbed, in order, is a good idea; poking them through holes in cardboard in a way that matches the orientation of the inner cover is a good way to do it as well.

Inner oil filter bolts, different lengths

Inner oil filter bolts, different lengths

Removing the inner filter cover

Removing the inner filter cover

One of the allen bolts holding the inner oil filter cover is tough to get to–the rear brake pedal prevents access to its head. Try different types of allen wrenches and sockets, and most importantly, press the rear brake down with one hand while putting the tool on the bolt with the other. Again, be careful not to strip out the allen bolt–it’s easy because of the awkward access. The inner cover should be carefully handled when you remove it, too, so you don’t harm its gasket. If it does get damaged, it must be replaced or it will leak.

Pressing down rear brake pedal to access that last pesky bolt

Pressing down rear brake pedal to access that last pesky bolt

At last, I arranged all the different-length bolts in order, removed the oil filter cover, and pulled out the oil, used oil filter.

Success! The old oil filter, accessible after removing the filter cover.

Success! The old oil filter, accessible after removing the filter cover.

With the filter removed, I checked the empty oil filter housing for debris, sludge, or other problems, wiping it out with a rag.

The oil filter housing, empty

The oil filter housing, empty

I placed the oil filter on its spike in my oil filter drainer. They can also be simply drained out over your oil pan, or on a spike or rack in the pan. Whatever method you use, the filter should drain at least overnight before you bag it in a ziploc bag and recycle it alongside your oil.

Old filter, in its filter drainer

Old filter, in its filter drainer

Now, it was time to install the new oil filter.

New filter ready to go

New filter ready to go

I checked all the o-rings and made sure I was inserting the new filter in the correct direction.

Inserting the new filter

Inserting the new filter

Carefully, I held the inner oil filter cover in place, and installed the varying-length bolts around its perimeter in the proper order. I torqued each bolt down gently but securely (the spec in the manual is 10Nm, or 7 ft-lb., so not much), not wanting any to strip or snap, and accessed the head of the last bolt by pressing down the rear brake pedal, as before. I also tightened the bolts in a diagonal or star pattern, so that the aluminum cover would not warp from uneven pressure.

Replacing the inner filter cover

Replacing the inner filter cover

Once the inner filter cover was secure, I replaced the outer filter cover.

Replacing the outer filter cover

Replacing the outer filter cover

With the new filter in place, I slid out the used oil pan and replaced the cap, setting it aside to recycle.

Pulling out the now-full oil pan

Pulling out the now-full oil pan

Making sure that the new crush washer was on the oil drain bolt, I re-inserted it and torqued it down firmly–but not harshly. You want to gently smush the crush washer without damaging the aluminum threads or case. If you use a torque wrench, the manual calls for 43 Nm (31 ft-lb) of torque on the drain bolt.

I opened the oil-filler cap and placed a long-necked funnel in the opening.

Funnel in place to re-fill the engine

Funnel in place to re-fill the engine

The oil capacity of the V-Star 650 is 2.97 quarts; the bike owner had 4 quarts on hand just in case–a wise move.

Fresh new oil

Fresh new oil

I poured in 2 quarts of oil, then figured I should check the oil sight glass to monitor the rising oil level. The sight glass is low on the left side of the bike; it’s easier to have an assistant hold the bike upright while you sit or crouch and look at the sight glass. It’s in the middle of the photo below.

The oil sight glass, just visible on the side of the engine

The oil sight glass, just visible on the side of the engine

I poured oil and checked the sight glass repeatedly, with my helper holding the bike upright, until the sight glass was completely full. I let the oil settle for a couple of minutes, then started up the bike and let it run for 3 minutes to circulate the new oil through the engine and filter. The level dropped somewhat, once I’d allowed the bike to cool for another 3-5 minutes, so I topped off the level and started the bike for another 3 minutes, then waited for another 3-minute cooldown.

Pouring in fresh oil

Pouring in fresh oil

After a couple of running and cooling down cycles, the oil level was perfect–almost to the top of the sight glass.

The V-Star 650, ready to ride. Glad that cardboard was there!

The V-Star 650, ready to ride. Glad that cardboard was there!

Glad that cardboard was there to prevent an oily mess in my driveway! The bike had a fresh oil and filter, and I put my tools away, cleaned up, and sealed the used oil in jugs and the used filter in my drainer for later recycling. I’m lucky enough to have an auto parts store that recycles oil a mile from my home, and that’s where I took the oil and filter for recycling.

Find out how to easily recycle your used oil and filters in San Mateo County, San Francisco, Alameda County, Sonoma County, Napa County, Marin County and Sacramento. If you’re not in those counties, find your own convenient oil and filter recycling location HERE.

Note: Several of these photos were taken by the bike owner, Sue Bennett. Thanks Sue, two hands are better than one!